This is the overview for the OdGeCircArc3d constructor overload.

Destructor for the OdGeEntity3d class. (Inherited from OdGeEntity3d)

(Inherited from OdGeCurve3d)

This is the overview for the appendSamplePoints method overload.

Determines the area of this curve between the specified parameters.
(Inherited from OdGeCurve3d)

This is the overview for the boundBlock method overload.

Returns the center of this arc.

This is the overview for the closestPointTo method overload.

Returns the point on this circle that is the closest to the specified plane, and the point on the plane that is the closest to this circle.

Returns a pointer to the 2D variant of the curve (z-coordinate will be ignored).
(Inherited from OdGeCurve3d)

Returns a copy of this entity. (Inherited from OdGeEntity3d)

This is the overview for the distanceTo method overload.

Gets the ending angle measured from the reference vector in the arc direction.

Returns the end point of this arc.

This is the overview for the evalPoint method overload.

Explodes this curve over the specified interval.
(Inherited from OdGeCurve3d)

This is the overview for the getClosestPointTo method overload.

Returns the geometric extents of this arc.

Returns the bounding box of the whole curve or a part of it. The box is axis-aligned in the specified local coordinate system. It is guaranteed to enclose the curve, but not guaranteed to be tight/minimal.
(Inherited from OdGeCurve3d)

This is the overview for the getInterval method overload.

This is the overview for the getLocalClosestPoints method overload.

Returns true, and the point on this curve whose normal vector passes through the specified point, if and only if a normal point was found.
(Inherited from OdGeCurve3d)

Returns the plane of the arc.

This is the overview for the getProjClosestPointTo method overload.

This is the overview for the getSamplePoints method overload.

Returns pointers to the two curves that result from splitting this curve at the point corresponding to param.
(Inherited from OdGeCurve3d)

Retrieves one or more trimmed offset curves.
(Inherited from OdGeCurve3d)

Returns true, and the end point, if and only if the parametric interval of this curve has an upper bound.
(Inherited from OdGeCurve3d)

Checks the boundaries of the curve interval and calculates a point from the curve interval that corresponds to the specified coefficient.
(Inherited from OdGeCurve3d)

Returns true, and the start point, if and only if the parametric interval of this curve has a lower bound.
(Inherited from OdGeCurve3d)

This is the overview for the intersectWith method overload.

Returns true if and only if this curve is closed within the specified tolerance.
(Inherited from OdGeCurve3d)

Returns true if the specified curve entity is coplanar with this curve and returns the common plane.
(Inherited from OdGeCurve3d)

This is the overview for the isDegenerate method overload.

Checks whether the specified entity is equal to this one.
(Inherited from OdGeEntity3d)

Returns true if and only if the specified point lies inside the full circle of this arc, and is on the same plane as this arc.

Returns true if and only if this entity is of type (or is derived from) entType.
(Inherited from OdGeEntity3d)

Returns true, and a linear entity coincident with this curve, if and only if this curve is linear.
(Inherited from OdGeCurve3d)

Returns true if and only if the specified point is on this entity, as determined by the tolerance.
(Inherited from OdGeEntity3d)

This is the overview for the isOn method overload.

Returns true if and only if this curve is periodic for the specified period.
(Inherited from OdGeCurve3d)

Returns true if and only if this curve is planar, and returns the plane of this curve.
(Inherited from OdGeCurve3d)

Attaches the specified curve to this arc.

This is the overview for the length method overload.

Calculates a point from the curve interval that corresponds to the specified coefficient.
(Inherited from OdGeCurve3d)

Mirrors this entity about the specified plane, and returns a reference to this entity.
(Inherited from OdGeEntity3d)

Returns the vector normal to the plane of this arc.

This is the overview for the orthoBoundBlock method overload.

Returns the entity that is the orthogonal projection of the curve onto the projection plane. (Inherited from OdGeCurve3d)

Returns the parameter of the point at a specified distance from the starting point corresponding to datumParam.
(Inherited from OdGeCurve3d)

This is the overview for the paramOf method overload.

This is the overview for the projClosestPointTo method overload.

Returns True if the projected points of the arc intersect with the specified linear entity, and returns the number of intersections and points of intersection.

Returns the entity that is the projection of the curve onto the projection plane in the specified direction. (Inherited from OdGeCurve3d)

Returns the radius of this arc.

Returns the reference vector as a unit vector.

Reverses the parameter direction this curve.
(Inherited from OdGeCurve3d)

Rotates this entity by the specified angle about the axis defined by the point and the vector, and returns a reference to this entity.
(Inherited from OdGeEntity3d)

Scales this entity by the scale factor about the basepoint, and returns a reference to this entity.
(Inherited from OdGeEntity3d)

This is the overview for the set method overload.

Sets the starting and ending angles of this arc, and returns a reference to this arc.

Sets the normal and reference vectors for this arc. Returns a reference to this arc.

Sets the center of this arc, and returns a reference to this arc.

This is the overview for the setInterval method overload.

Sets the radius of this arc, and returns a reference to this arc.

Gets the starting angle measured from the reference vector in the arc direction.

Returns the start point of this arc.

This is the overview for the tangent method overload.

Applies the 3D transformation matrix to this entity, and returns a reference to this entity.
(Inherited from OdGeEntity3d)

Applies the 3D translation vector to this entity, and returns a reference to this entity.
(Inherited from OdGeEntity3d)

Returns the entity type. (Inherited from OdGeEntity3d)

Comparison operator for the OdGeEntity3d object.
(Inherited from OdGeEntity3d)

Assignment operator for objects of the OdGeCircArc3d class.

The assignment operator for objects the OdGeCurve3d class. (Inherited from OdGeCurve3d)

Assignment operator for the OdGeEntity3d object.
(Inherited from OdGeEntity3d)

Comparison operator for the OdGeEntity3d object.
(Inherited from OdGeEntity3d)